Mac Tools Tl90 Timing Light Manual

Mac Tools Social Media. Mac Tools Customers are proud to show that Mac Tools are Great to Work With™. So, we are eager to have you connect with us via Facebook, Instagram, and Twitter to share your experiences with the brand, our products, partners, and our entire Mac Tools team. If you are a resident of, or wish to acquire a franchise for a Matco Tools distributorship to be located in, one of these states or a country whose laws regulate the offer and sale of franchises, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your.

How to use a timing light, and how to adjust your timing.

Step 1

Whether man or woman, it is always good to read the instructions first, no matter what you are doing. You can use the picture here as an example, but hook up your timing light as instructed by your manual. Most all timing lights have three clips on them and these instructions will discuss those types. How to Use a Timing Light Make sure the auto engine is off and the key is removed from the ignition. For the next steps, make sure the battery terminals are clean enough to allow for a good connection. If not, then clean as required being cautious not to allow any contact on your skin because this is battery acid. If it does come in contact, then just wash with soap and water.

Step 2

Clamp the red clip to the positive terminal of your car battery.

Step 3

Clamp the black clip to the negative terminal of your car battery.

Step 4

The largest clip (the one with the thickest insulation) goes on your #1 spark plug wire by attaching the clip around the wire that leads to your #1 spark plug.

Step 5

Timing Light Advance Auto

Next, you will want to rotate the lower crankshaft pulley so that it has the timing marks called out on the crankshaft pulley. Be aware that on some cars the timing marks are located somewhere else and you should consult either your owner's manual (another instruction manual), or automobile dealer. You may also see a pointer on the engine block that will point to these marks as well.

Step 6

Your auto's spec sheet should tell you what your timing degree should be. For example, a 1969 Ford 429, 6 Degrees BTDC @ 550 rpm in drive gear - with automatic trans, with a firing order of 1-5-4-2-6-3-7-8. All this means is that you want to line up the pointer on the timing light with the 6째 timing mark when the engine is idling in gear at 550 rpm. As you can see, it also says something about 'BTDC' for this Ford. There is also an 'ATDC.' 'Before Top Dead Center' and 'After Top Dead Center' - top dead center is the point where the piston reaches the highest point in the cylinder and that is when the compression is the greatest. Now, your timing marks with have a line labeled '0' with marks above and below it, and depending on which way the wheel rotates, you will see the lines before the '0' (BTDC), or after the '0' (ATDC).

Step 7

Mac Tools Tl90 Timing Light Manual Download

If you want, you can use some chalk to mark the timing marks to make them more visible. Then, on the side of the distributor, disconnect the rubber hose from the vacuum advance and put a piece of duct tape on the end of the hose to seal it off.

Step 8

Okay, now start up your engine, letting it warm up. We will assume that your auto is properly idling, otherwise, if the idle is off, and your mechanical advance may influence your timing adjustment.

Step 9

Take your timing light and aim it at the timing marks, pressing the button on the light. Because you have the light hooked up to your spark plug means that it has current passing through it every time your spark plug fires, making the light go off and on, creating the strobe effect. Because of this, the timing marks should appear to be standing still. Now, is that pointer (earlier described) pointing at the correct mark? If yes, you are all set, you do not need to adjust your timing. You are good to go! If it is not, you should adjust your timing. See the next steps to adjust the timing.

Step 10

Adjusting the Timing Below the distributor, at the base of your distributor shaft, is a fastener called the distributor hold-down clamp. We want to loosen this fastener so the distributor can turn on the shaft. Grasp the vacuum advance and move it back and forth.

Step 11

Rotate the distributor slightly, then aim your timing light back at the timing marks again. How does it look? If it is farther away from the marks, then move the distributor in the opposite direction. Then, check again with your timing light. Continue doing this until the pointer is pointing at the correct degree point as required.

Step 12

Once the timing is good, re-tighten the fastener for the distributor hold-down clamp, making sure you do not move the distributor!! After re-tightening this fastener, just double check your timing again to make sure -- tightening the distributor may change your timing.

Turn off your engine, remove the key from the ignition, and disconnect the timing light. That is all there is to it! You have done well! Pat yourself on the back after you wash your hands!

Tips

  • Have all your tools gathered so this is easier.
  • Use some type of fender cover so you do not scratch the paint.
  • Do not forget to remove all your tools from the engine when you are all finished.
Mac Tools Tl90 Timing Light Manual

Warning

  • Be careful as you are working with your auto's electrical system, which, if not done correctly, you may find yourself getting hurt.

Items you will need

  • Timing Light
  • Tool, such as a combination wrench, to loosen Distributor
  • Duct Tape
  • Draper Tool Company Timing Light Manual

More Articles